Your search for Al alloy resulted in 18 matches...
The paper presents the results of examinations of composite samples in which the reinforcement is waste fly ash from power plants, while matrix is an aluminium (A8). The agglomerates of master composite obtained by...
more >>
As expected, the increasing demand for magnesium alloy castings has already become a fact. Considering this situation, a rich program of the studies on this particular subject has been initiated and put into operat...
more >>
The article is a compilation of the most important results obtained during execution of own research project regarding the possibility of using fly ash formed during combustion of hard coal as a base granular material ...
more >>
Nanomaterials extend the range of their application in human activities. The past few years have faced a considerable increase of interest in various aspects of the application of nanotechnology in liquid phase met...
more >>
The paper presents the results of examinations of composite samples in which the reinforcement is waste fly ash from power plants, while matrix is aluminum (99,98 wt.%). The agglomerates of master composite obtained by mechanical alloying were sub...
more >>
The aim of this study was to determine the impact of technological factors (surface treatment and contact time) on the kinetics of wetting of nickel substrates by a liquid aluminum alloy. Wetting kinetics studies were carried out in vacuum at 700&...
more >>
The article presents results of an investigation which constitutes a section of research under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies", one of the aims which is the introduction of new ecological inorganic binders...
more >>
One of the factors which influence development tendencies within the scope of moulding sands used in foundry practice is environmental protection. Hence, while assessing technologies, the composition of utilised materials and emissions of harmful ...
more >>
In this study a simple procedure for the in situ identification of the intermetallic phase precipitates in the interdendritic eutectic in both wrought and cast AlFeMnSi alloys has been established and then verified by ...
more >>
In this work, an analysis of the solidification course of the AlFeMnSi alloys was carried out in the Al alloys of Fe, Mn, and Si concentrations in a range supplementary for those examined until now. The morphology of the pre-dendrite and pre-eutec...
more >>
The paper presents research on the possibility of improving the plasticity of near-eutectic AlSi11 alloy by the use of soft annealing treatment. For two assumed input quantities, i.e. temperature and duration of the soaking treatment, based on the...
more >>
The procedures of grain refinement and modification of a silicon eutectic in hypo- and transeutectic silumins belong to important factors shaping their microstructure as well as physico-mechanical and technological properties. Due to this fact, th...
more >>
The sessile drop method was adopted to investigate the effect of multiple re-melting and casting of metal matrix composite on the structural stability of metal-ceramic slurry. Commercial aluminum matrix composite made of the A359Al alloy reinforce...
more >>
The paper presents the results of the study of Al-Si alloys with a vanadium addition used in pressure casting. The hypoeutectic Al-Si alloy grade EN AC-46000 was applied as the initial alloy. The master alloy AlV10 was introduced into the initial ...
more >>
During the project a technology of making ceramic moulds using aluminosilicate microspheres was developed. According to the developed technology, ceramic samples were used to determine thermal conductivity in the temperature range of 500°C to ...
more >>
This article presents a method of melting zirconium alloy in an induction vacuum furnace using a thermally insulated graphite crucible. The design of the Supercast Titan induction centrifugal furnace allows for the quick melting of metal alloys in...
more >>
The designing of new light-weight alloys for continuous replacement of cast iron and steel parts is now the mainstream regarding energy saving and improvement of fuel consumption in the transportation sector. Parallel with the remarkable advances ...
more >>
This study includes the results of tests related to selecting the data collection parameters for EBSD analysis, correction and modification of the EBS diffraction patterns, and use of selected functionalities of the commercial OIM s...
more >>
| 
